new Origin New Rear Window Nut for Aixam and Minauto All Aixam and Minauto Models The rear window nut (often a plastic cap nut or a shouldered metal nut) is an essential technical fastening component located on your microcar's tailgate. It secures and holds the rear wiper motor shaft or the hinge mounting through the rear window glass. Subjected to constant vibrations generated by the twin-cylinder diesel engine, this nut tends to loosen over time, crack (if made of plastic), or seize due to rust. A loose or damaged nut can cause play in the rear wiper arm, knocking noises, and dangerous water leaks into the luggage compartment. €6.90 Add to cart
new Adaptable New Rear Wheel Hub for Microcar MGO 1 Microcar MGO 1 The rear wheel hub is a key chassis component of your first-generation Microcar MGO 1. Mounted at the end of the trailing arm or rear axle, it supports the wheel bearing and houses the wheel studs that securely fasten the wheel rim. Constantly exposed to road impacts, moisture, and heavy loads, the hub can wear out over time. Typical signs of a worn rear hub or wheel bearing include a whistling or low humming noise that increases with speed, excessive wheel play when the vehicle is lifted, and unusual vibrations inside the cabin. €83.90 Add to cart
new Origin New Interior Rear View Mirror for Aixam and Minauto Aixam 300, 400, 500, 400.4, 500.4, 500.5, A721, A741, A751, City, City S, Roadline, Scouty, Crossline, City, Crossover, GTO, Coupé, Mega Phase 2, and all Minauto models. The interior rear view mirror is a mandatory safety component that ensures clear rearward visibility and helps reduce blind spots during manoeuvres, overtaking, and braking. On Aixam and Minauto microcars, the central mirror is exposed to the strong vibrations typical of twin-cylinder diesel engines. €29.90 Add to cart
new Adaptable New Plastic Wheel Chock The wheel chock is a mandatory passive safety accessory designed to prevent any accidental movement of a parked or jacked-up vehicle. Whether used to stabilise an unhitched trailer or caravan, secure a microcar on sloping ground, or ensure perfect immobilisation during mechanical work in a workshop, the wheel chock is an essential safeguard against the risk of unintended rolling. Made from high-density technical polymers, our wheel chocks provide an excellent alternative to heavy metal or rubber models that are prone to corrosion. €15.90 Add to cart
new Adaptable New 12V/230V Mini Compressor Driving with the correct tire pressure is essential for your safety, the handling of your two-wheeler, and the control of your fuel consumption. The 12V/230V mini compressor is the ultimate portable tool. Thanks to its hybrid dual power supply, it can be connected either to a 230V mains outlet in your garage or workshop for weekend maintenance, or to your car or scooter’s 12V cigarette lighter socket for emergency inflation at the roadside. Compact and lightweight, it easily fits in a trunk, top case, or backpack. €39.90 Add to cart
new Adaptable New Chatenet CH46 Windshield Chatenet CH46 The windshield is a key element of the passive safety system of your Chatenet CH46. Beyond its obvious function of protecting against wind, rain, and road debris, it actively contributes to the structural rigidity of the passenger compartment of your driverless car. An impact in the driver’s field of vision, a crack spreading due to frost or heating, or glass that has become cloudy over the years can seriously compromise your visibility. To drive with peace of mind and pass the roadworthiness inspection for microcars without issues, replacing damaged glazing is essential. €249.90 Add to cart
new Origin New Daytime Running Light Ligier, Microcar and Casalini Ligier JS50 Sport (ph1), Ligier JS50L Sport (ph1), Microcar Mgo 3, Dué 2 P85, Casalini M14 2.0, M20, 550 Daytime running lights (or LED daytime lights) are not designed to illuminate the road, but to make your vehicle more visible to other road users as soon as the engine is running. On recent driverless cars from the Ligier, Microcar, and Casalini brands, these streamlined LED strips create the vehicle’s distinctive visual signature. €119.90 Add to cart
new Origin New Battery Holder for Microcar MGO 2, M8, F8C and Ligier JS... Microcar MGO 2, M8, F8C and Ligier JS RC with Lombardini DCI Engine The battery holder (generally consisting of the metal retaining bracket, threaded rod, and fastening nut) is a passive safety component that keeps the battery securely fixed in its tray. On the Microcar MGO 2, M8, F8C, and Ligier JS RC models equipped with the twin-cylinder Lombardini DCI (Common Rail) engine, this part is particularly important. Although the DCI engine is more modern and delivers higher torque, it also generates significant structural vibrations at idle, which are transmitted throughout the engine compartment. €29.90 Add to cart
new Origin New Rear Engine Mount for Microcar MGO 2 and M8 Microcar MGO 2 and M8 The rear engine mount (often referred to as the rear silent block or gearbox mount) is the pivotal component that connects the rear of the engine and gearbox assembly to the subframe or the aluminum chassis of your vehicle. On the Microcar MGO 2 and Microcar M8 models (whether equipped with the Lombardini Progress or DCI engine), the twin-cylinder diesel engine naturally produces strong vibrations and significant rocking movements, particularly during starting, acceleration, and deceleration. €59.90 Add to cart
new Origin New Left Front Bumper Grille for Aixam City and Coupé from... Aixam City and Coupé from the Ambition Range The left front bumper grille (driver’s side) is a bodywork component clipped or screwed into the side opening of the front bumper. On Ambition generation City and Coupé models, this grille serves both an aesthetic and functional purpose. €30.50 Add to cart
new Origin New Diesel Fuel Pump Filter for Aixam and Minauto Ambition Range Aixam City, Coupé, Crossline, Crossover and Minauto Ambition Range The diesel fuel pump filter (or replacement cartridge) is the consumable component installed inside the filter bowl or directly screwed underneath the pump head. On the Aixam and Minauto Ambition generation equipped with the Kubota diesel engine, this filter captures even the smallest impurities (dust, tank residues, carbon deposits) and separates the water present in fuel from service stations. €50.60 Add to cart
new Origin New Gasket Set for Aixam and Minauto with Kubota Z482-E5B Engine Aixam and Minauto with Kubota Z482-E5B Engine The complete gasket set includes all sealing gaskets, oil seals, and washers required when opening or rebuilding an engine. On the Kubota Z482-E5B twin-cylinder diesel engine (the latest generation complying with Euro 5 emission standards) fitted to recent Aixam and Minauto models, maintaining perfect sealing is essential. €222.40 Add to cart
new Origin New Alternator for Aixam and Minauto Ambition Range Aixam and Minauto Ambition Range The alternator is the heart of your vehicle’s electrical system. Driven by the Kubota twin-cylinder diesel engine via an accessory belt, its role is twofold. On the Ambition generation (Aixam City, Coupé, Crossline and Minauto), the charging system is particularly heavily used due to modern onboard electronics. Exposed to constant vibrations from the diesel engine, high temperatures under the hood, and humidity, the alternator (or its integrated voltage regulator) may eventually fail. €420.90 Add to cart
new Origin New Fan for Casalini Sulky, M20 and 550 Casalini Sulky, M20 and 550 with air conditioning Ensure optimal cooling for your driverless car with this original manufacturer Casalini cooling fan. Specifically designed for high-end models equipped with an air conditioning system, this fan motor assembly provides the necessary airflow to regulate both engine temperature and the needs of the air conditioning condenser. €198.20 Add to cart
new Origin New INTAKE VALVE FOR AIXAM AND MINAUTO AMBITION RANGE Aixam and Minauto with Kubota Z482-E5B Engine The intake valve is a key component of the cylinder head. On the Kubota twin-cylinder diesel engine used in the Aixam and Minauto Ambition generation, its role is to open and hermetically close the air intake passage. Operated by the camshaft through the rocker arms, it opens to allow fresh filtered air into the cylinder for optimal diesel fuel combustion, then closes immediately to ensure complete engine sealing during the compression phase. €45.60 Add to cart
new Origin New Intake Valve Guide – Kubota Engine, Aixam Aixam for Kubota engines Z402, Z482, Z602, Z482-E4B, Z602-E4B, Z482-E5B Optimize your engine's performance and compression with this genuine manufacturer intake valve guide. Specially designed for Kubota engines used in Aixam light vehicles, this part ensures perfect valve alignment and maximum thermal resistance. €14.20 Add to cart
new Origin New Fuel Pump Filter Seal Kit for Aixam and Minauto Ambition... Aixam and Minauto with Kubota Z482-E5B Engine The fuel pump filter seal kit includes all the O-rings and washers required to ensure the fuel filtration unit is properly sealed. On Aixam and Minauto models from the Ambition generation range (powered by the Kubota twin-cylinder diesel engine), the fuel pump (mechanical or electric depending on the version) pushes diesel fuel through a filter bowl or cartridge before sending it to the injection pump. €28.20 Add to cart
new Origin New Valve Cap for Aixam and Minauto Aixam for Kubota engines Z402, Z482, Z602, Z482-E4B, Z602-E4B and Z482-E5B The valve cap (often called a valve stem cap) is a small cylindrical metal cap made of very hard steel that fits directly onto the upper end of the valve stem. On the Kubota twin-cylinder diesel engine used in Aixam and Minauto ranges, this part acts as a buffer zone: it is the surface on which the rocker arm strikes thousands of times per minute to push the valve down and open the combustion chamber. €7.20 Add to cart
new Origin New Valve Keeper (Half-Moon Valve Collet) for Aixam and Minauto Aixam for Kubota engines Z402, Z482, Z602, Z482-E4B, Z602-E4B and Z482-E5B The valve keeper (also known as a valve collet or valve lock) is a small semi-cylindrical and tapered metal component. Always used in pairs (two keepers per valve), it fits into the grooves of the valve stem and locks into the upper spring retainer. On the Kubota twin-cylinder diesel engine used in Aixam and Minauto vehicles, these small retainers have the critical task of keeping the valve spring compressed to ensure the valve remains properly closed. €16.40 Add to cart
new Origin New Thermostat for Aixam and Minauto Ambition Range Aixam and Minauto with Kubota Z482-E5B Engine The thermostat (commonly called a calorstat) is a mechanical thermostatic valve located in the cooling system. On Aixam and Minauto Ambition range models (powered by the Kubota twin-cylinder diesel engine), it acts as a thermal “regulator”. €48.50 Add to cart
new Origin New Temperature Sensor for Aixam and Minauto Ambition Range Aixam and Minauto with Kubota Z482-E5B Engine The temperature sensor (or thermistor) is the thermal safety sensor screwed directly onto the engine cylinder head or onto the thermostat housing. On Aixam models (City, Coupé, Crossline) and Minauto models from the Ambition generation range (equipped with the Kubota twin-cylinder diesel engine), this sensor measures the coolant temperature in real time. €89.60 Add to cart
new Origin New Engine Subframe for Aixam Mega Aixam Mega (Phase 1) The engine subframe (or lower cross member) is the most important cast or steel fabricated component in the front section of the vehicle. On Aixam Mega utility vehicles (particularly MultiTruck, Worker, or e-Worker versions, equipped with Kubota diesel engines or electric power units), the subframe serves as a rigid foundation. €376.40 Add to cart
new Origin New Cooling Fan for Casalini Ydea, Sulky and Kerry Cooling Fan for Casalini Ydea, Sulky and Kerry Ensure the longevity and performance of your microcar with this genuine manufacturer cooling fan. Specifically designed for Casalini models, it provides optimal airflow to regulate your engine temperature, helping prevent the risk of overheating. €157.90 Add to cart
new Origin New Front Bumper for Aixam City and Coupé Ambition Range Aixam City and Coupé Ambition Range The front bumper is the centerpiece of your microcar's bodywork. Specifically designed for the Aixam Ambition range (available on the City and Coupé models), this bumper incorporates the upper grille and gives the vehicle the modern, dynamic look that characterizes this generation. €379.90 Add to cart
new Origin New Fuel Level Sender for Casalini M20 and 550 Casalini M20 (2nd version) and 550 The fuel level sender (or fuel level sensor) is the electronic and mechanical component installed directly inside the fuel tank. On Casalini M20 and M20 550 models (equipped with Kohler twin-cylinder diesel engines), this part uses a float arm system connected to a variable electrical resistor (potentiometer) to accurately transmit the remaining diesel fuel level directly to the gauge or display on your dashboard. €92.90 Add to cart
new Origin New Fan Switch Sensor for Casalini Casalini Ydea, Sulkydea, Sulky Pick-Up, Kerry, Sulky, M10, M12, Pick-Up 12, M14, M20 and 550 The fan switch sensor (technically called a radiator thermal switch) is the independent switch of the cooling system. Screwed directly onto the body of your Casalini’s coolant radiator (equipped with Mitsubishi or Kohler twin-cylinder engines), this sensor is in direct contact with the coolant. €16.80 Add to cart
new Origin New Electric Blower Fan for Casalini Casalini Ydea, Sulky flatbed and Pick-Up, and Kerry The electric interior blower fan (also called an air blower motor or heating turbine) is the core component of your microcar’s ventilation system. On Italian Casalini models, this electric motor drives a cylindrical bladed turbine to draw in outside air, push it through the heater core (and the air conditioning unit if equipped), then distribute it through the air vents towards the windscreen and the passenger compartment. €157.90 Add to cart
new Origin New Radiator Fan for Casalini Casalini Sulky, M10, M110, M12, Pick-up 12 and M14 with air conditioning The radiator fan is the active cooling system of your microcar. On Italian Casalini models (generally equipped with powerful twin-cylinder diesel engines such as Mitsubishi or Kohler), the water radiator located at the front requires a constant airflow to dissipate the heat from the coolant. €218.60 Add to cart
new Origin New Oil Separator Connector Hose for Greaves E5+ Engine Greaves E5+ Engine The oil separator connector hose (often called a connecting sleeve or bypass connector) is the intermediate part that provides the direct connection between the valve cover outlet (upper engine section) and the oil separator housing inlet, or between the separator and the rigid intake pipe. On the Greaves E5+ twin-cylinder diesel engine fitted to Ligier JS50 and Myli models, this connector plays a key role in maintaining the engine’s internal vacuum. €19.90 Add to cart
new Origin New Engine Oil Hose for Greaves E5+ Engine Greaves E5+ Engine The engine oil hose (depending on its location: upper engine oil supply, connection to an oil cooler, or pressure return line) is a component exposed to extreme operating conditions. On the Greaves E5+ twin-cylinder diesel engine fitted to Ligier JS50 and Myli models, the oil does not simply remain static: it is driven by the pump at a pressure that can exceed 3 to 4 bar when the engine is hot. €7.90 Add to cart
new Origin New Oil Separator Hose for Greaves E5+ Engine Greaves E5+ Engine The oil separator hose (or breather hose) connects the valve cover to the oil separator, or the oil separator to the air intake manifold. On the Greaves E5+ twin-cylinder diesel engine fitted to specific versions of the Ligier JS50 and Myli, this hose is the mandatory path for evacuating excess air pressure and oily gases generated inside the engine crankcase. €9.90 Add to cart
new Origin New Engine Pressure and Temperature Sensor for Greaves E5+... Greaves E5+ Engine The pressure and temperature sensor (often referred to as a combined sensor or TMAP sensor) performs two essential functions in a single component. Installed directly on the intake manifold of the Greaves E5+ twin-cylinder diesel engine (fitted to certain versions of the Ligier JS50 and Myli), it simultaneously measures intake air pressure and temperature. €89.90 Add to cart
new Origin New Exhaust Manifold for Greaves E5+ Engine Greaves E5+ Engine The exhaust manifold is a robust cast iron or steel component bolted directly to the cylinder head. On the Greaves E5+ twin-cylinder diesel engine fitted to Ligier JS50 and Myli models, its role is to collect the exhaust gases leaving both cylinders at very high temperatures and channel them into the exhaust system (including the catalytic converter and muffler). €179.90 Add to cart
new Origin New Exhaust Manifold for Greaves E5+ Engine For Greaves E5+ Engine The exhaust manifold is a robust cast iron or steel component bolted directly to the cylinder head. On the Greaves E5+ twin-cylinder diesel engine fitted to Ligier JS50 and Myli models, its role is to collect the exhaust gases leaving both cylinders at very high temperatures and channel them into the exhaust system (including the catalytic converter and muffler). €39.90 Add to cart